 |
 |
 |
The Temporary Fencing System with all the Advantages |
 |
 |
 |
 |
 |
|
 |
|
 |
|
 |
 |
Edge Protection Fencing
 Simple lock-in installation |
|
|
|
|
|
| Maximum protection |
|
|
|
|
|
| Built in safety kickplate |
|
|
|
|
|
| Re-usable asset |
|
|
|
|
|
| Complies to AS 1657-1992 |
|
|
|
|
|
This simple to install system offers site personnel maximum protection on the perimeter of construction slabs, around stair and lift wells, excavations etc. The removable panels, with built-in kickplates, and post system is easily transported, installed removed and stored.
CCS Edge Protection Fence Panel
This 1000mm high x 2400mm galvanised welded panel is manufactured from 4mm steel wire at centres not exceeding 50mm x 50mm to comply with AS/NZS 4576 - 1995 'Guidelines for Scaffolding'. Each panel features a rectangular rolled top and triangular bottom incorporating a galanised kickplate that helps prevent objects from falling through the panel bottom.
Galvanised Posts
Galvanised posts are available in RHS 50mm square manufactured to comply to AS1657 - 1992 'Fixed Platform, Walkways, Stairways and Ladders - Design, Construction and Installation'. CCS Industries posts comply with design loads and coating protection.
The Slide and Lock Square Post
The 1005mm high post incorporates top and bottom wite panel holding lugs with slide and lock assemblies, making panel installation and removal quick and simple. The bottom 152mm x 152mm x 5mm thick fixing flange and plastic cap completes the assembly.
The Fence System Components
 |
 |
 |
 |
| The Panel | The Slide and Lock Post |
The Kickplate | The Fixing Flange |
Unit Sizes
| Panel |
| Wire: Ø 4 mm |
| Mesh: 50 mm x 50 mm centres |
| Overall: 1000 mm high x 2400 mm wide |
| Product Code: EDPR 10 |
| Finish: Pre-galvanised |
| Mass: 13.14 kg |
| Slide and Lock Post |
| 1000 mm - 50 mm x 50 mm x 1.6 mm |
| Product Code: EP 5050 |
| Type: Black RHS |
| Finish: Hot dipped galvanised |
| Mass: 2.5 kg |
| Kick Plate |
| 150 mm x 2400 mm galvanised sheet, locked into the panel |
| Fixing Flange |
| 152 mm x 152 mm x 5 mm hot dipped galvanised steel plate |
Fixings
Fixings should conform with AS4100 for permissible working strength and size of bolts. The recommended fixings are four 12 mm x 75 mm Dynabolts - supplied by others - securely fastening each post fixing flange to the concrete slab, stairwell, walkway, etc.
Installation
Two people can easily erect the Edge Protection Fencing System.
Start from an appropriate point on the site and fix the first post through the bottom flange with 4 - 12mm x 75mm Dynabolts with the Slide and Lock assemblies facing into the building.
Attach the fence panel to the post using the Slide and Lock assemblies. Note the rolled top and bottom of the panel face inside allowing the panel to fit flush against the post.
Attach the other end of the fence panel to a second post. Dynabolt the second post to the concrete and then tighten the fixings to the flange.
Attach a second panel to the second post as previous and repeat until project is complete.
Important Safety Note: With the Slide and Lock posts extra security is achieved by locking the latch using self-tapping screws in the hole provided at the back of the Slide and Lock assembly.
Edge Protection Fencing Brochure in PDF format.(4.27 Mb)
[home] [product features] [product range] [get a quote] [contact us]
